Farmall Cub #22 mower belt guard in good condition, $65.00
Original 4 bar grill assembly in restorable condition $125.00
90 degree flat belt pulley drive with pulley fitting Farmall Cub tractors equiped with PTO. This drive assembly can be used to power equipment powered with an endless flat belt or is needed to...
Adjustable wide front axle clamps $20.00 each
Air cleaner assembly $25.00
Air cleaner to engine breather tube $5.00
Air intake pipe $20.00
Battery cable frame clamp $5.00
Brake drum with axle locking bolt $25.00
Camshaft and cam gear $25.00
Farmall Cub Zenith carburetor removed from a running tractor. Tractor ran but had been sitting for a few years, carb may need rebuild, $150.00
Choke rod $15.00
Clutch housing with all good mounting holes $75.00
Clutch inspection cover $10.00
Set of pistons and rods $50.00
Set of 15 cylinder head bolts $15.00
Dipstick $10.00
Drawbar with mounting plates $150.00
First generation hood and gas tank. Gas tank is VERY clean but does have one slight dent. Hood is great but will need one headlight post nut welded back on. $200.00
Fan and pulley assembly $25.00
Right hand final drive with axle and brake drum $125.00. Also have internal parts from the left drive which was broken and welded up, contact me with your needs.
Dent free final drive axle pans $20.00 each
Flywheel $40.00
Front battery box cover hold down $5.00
Front screw in hub caps $10.00 each
Front spindles that had the outer steering arms welded to them on the top $15.00 each
Front wheel hubs $15.00 each
Set of 10 tapered head front wheel to hub bolts $20.00
Fuel line from a running tractor $5.00
Governor assembly $50.00
Farmall Cub grill doglegs $45.00 for the pair
Farmall Cub headlight stand off posts $20.00 for the pair
Farmall Cub complete hydraulic or touch control removed from a running tractor. Assembly includes everything shown to add hydraulics to your Cub without hydraulics, $450.00
Hydraulic manifold lines $100.00
Rear lift or rockshaft assembly for Farmall Cub tractor with factory hydraulics. This lift mounts to the top of the transmission and is used to lift rear cultivator gangs, disc, 1 bottom plow or 7...
Idler gear $10.00
Brake pedal with lock arm $10.00
Lower water neck $15.00
Oil filter cover and hold down bolt $10.00
Oil pump $20.00
Oil pump screen and pick up tube $15.00
Pair of outer spindle arms that were welded to the tops of the spindles but are not bent or welded $30.00
Very nice, straight and solid pair of fenders $100.00 for the pair with 3 pair available and also a single for $50.00 if you only need one.
Do you have a Farmall Cub with one bottom plow that you just can’t make work? Does your plow just skip along the sod? Well here’s the solution. This depth lever and dog bone link are...
Front steering / radiator casting $300.00
Farmall Cub radiator removed from a running tractor. Radiator has slight tweak but is still good and will work on your working tractor, $75.00
Radiator mounting support set $25.00
Very nice pair of rear rust pit free center hubs with good mounting holes $75.00 for the pair
Pair of Cub rear lift rods and springs $50.00
Cub rear toolbar mount, believe it to be for the right side $40.00
Rear hand lift assembly to fit Farmall Cub tractors without factory hydraulics. This lift bolts on top of the transmission and is used to lift rear mounted implements such as a cultivator, digger,...
Set of 10 rear tapered head hub to axle mounting bolts $20.00
Rear main seal housing $15.00
Right hand axle housing $50.00
Farmall Cub seat suspension post, $75.00
Farmall Cub sickle mower pulley. 99% of the time this pulley is not included with the mower or the splines are worn out. This pulley is ready to install and go to cutting. $100.00
Steering post with upper mount $20.00
Tapered head drawbar or implement mounting bolts $5.00 each
Tappit cover $15.00
Throttle rod $10.00
Throw out bearing with mount from a running tractor $20.00
Transmission with input shaft from a non-running tractor $150.00
Upper water neck $15.00
Complete wide front as pictured $200.00. Also have some other front end parts to sell separately or will disassemble one to help with your needs
Work light mount $15.00
